DC Power & BEC Series

FCHUB-6S w/ Current Sensor 184A, BEC 5V & 10V

This FCHUB was designed to be paired with the Matek F405 Mini. Together they work as a great combo for any build. Both the FCHUB and F405 Mini can be connected using a flat ribbon cable, which simplifies your build process and takes up less space

Specifications

Brand name: Matek Systems
Item name: FCHUB A5
Input: 6-27V (2-6S Lipo)
Input TVS protection
PDB: 4x35A (Max. 4x46A)
BEC: 5V 2A (Max. 2.5A)
Current sensor: 184A
Current scale: 179
BLHeli32 ESC telemetry pads
Weight: 8g
Size: 46x36x4mm
Mounting holes: 30.5mm & 20mmφ3mm
Ribbon cable connection with FC F405-mini

Includes

1 x FCHUB A5
6 x screws M3*11
6 x nylon nuts M3

FCHUB-A5 w/ Current Sensor 184A, BEC 5V 2A SKU: FCHUB-A5

Specifications

Brand name: Matek Systems
Item name: FCHUB A5
Input: 6-27V (2-6S Lipo)
Input TVS protection
PDB: 4x35A (Max. 4x46A)
BEC: 5V 2A (Max. 2.5A)
Current sensor: 184A
Current scale: 179
BLHeli32 ESC telemetry pads
Weight: 8g
Size: 46x36x4mm
Mounting holes: 30.5mm & 20mmφ3mm
Ribbon cable connection with FC F405-mini

Includes

1 x FCHUB A5
6 x screws M3*11
6 x nylon nuts M3

Fixed Wing PDB FCHUB-W

PDB

Input voltage range: 9~30V (3~6S LiPo) w/TVS protection
2x ESC power pads
Current Senor: 104A, 3.3V ADC, Scale 317
4x BEC on board
3x LED indicators for 5V, 10V & Vx

Soldering Holes & Pads

+ & – : Bettery & ESC power pads
Curr: Current sensor output
Vbat: Bettery voltage
G: Ground
3V3: LDO 3.3V
5V: BEC 5V
10V: BEC 10V
Vx: BEC 5V/6V/7.2V ADJ

FFC connection

Compatible with MATEKSYS FC F405-STD, F722-STD, F405-OSD
MT1: Motor1 of INAV Flying Wing & Airplane
MT2: Motor2 of INAV Flying Wing & Airplane
SV3~SV6: Servo 3~6 of INAV Flying Wing & Airplane
VTX: Video Transmitter signal
TX5 & RX5: UART5 of F405-STD/F722-STD/F405-OSD

BEC 5V output

Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, GPS module
DC/DC synchronous buck regulator
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps, Max.3A
Output Ripple: 20mV (VIn=24V, VOut=5V@2A load)
Short-circuit tolerant (2 seconds)

BEC 10V output

Designed for Video Transmitter, Gimble
DC/DC synchronous buck regulator
Voltage: 10.0 +/- 0.2VDC (Input voltage >11V)
Continuous current: 2 Amps, Max.3A
Output Ripple: 20mV (VIn=24V, VOut=10V@2A load)
Short-circuit tolerant (2 seconds)

BEC Vx output

Designed for Servos
DC/DC synchronous buck regulator
Voltage adjustable, 5V Default, 6V or 7.2V via jumper
Continuous current: 5 Amps, Max.5.5A
Output Ripple: 50mV (VIn=24V, VOut=5V@5A load)
Short-circuit tolerant (2 seconds)

BEC 3.3V output

Designed for Baro / Compass module and Spektrum RX
Linear Regulator
Continuous current: 500mA

Physical

Mounting: 30.5 x 30.5mm, Φ3mm
Dimensions: 52 x 36 x 6 mm
Weight: 13g

Linear Regulator 4S LiPo to 12V 300mA

Generally the input voltage of FPV camera is 7~13V, When 4S LiPo is mounted, the linear regulator can convert 14~17V to 12V, and power camera & 12V 1W LED without ripple & noise.

25*10mm PDB, 1g, Small & Light.
Input: 4S LiPo, Output: 12V, Cont.300mA

Micro BEC 6-30V to 5V/9V-ADJ

High Efficiency Synchronous Step-down regulator
Wide 6V to 30V Operating Input Range
Continuous load current: 1.5 Amps (Max.2.5A 5s/minute)
VOut 5V or 9V Adj. Default is 5V.
VOut Load Regulation: 2%
Standby current: <5mA
Maximum Duty Cycle: 95%
OCP Protection and Hiccup
Thermal Shutdown
Output Short-circuit tolerant (5 seconds/minute)
Pins distance: 2.54mm
Size & Weight: 10x14x3mm, 1g
Packing: 3pcs/unit

Micro BEC 7-21V to 5V/12V-ADJ SKU: MBEC2A

Matek Micro BEC 5V/12V-Adj

A Highly efficient synchronous rectified step-down switch mode converter. It offers a very compact solution to achieve 1.5A continuous output current over a wide input supply voltage (7 to 21V).

Features:
• High-Efficiency Synchronous Mode
• Wide 7V to 21V Input range
• Voltage output can be 5V or 12V adjustable. (default is 5V)
• OCP Protection and Hiccup
• Thermal Shutdown
• Output Short-circuit tolerant (5 sec/minute)

Specs:
Continuous load current: 1.5A (Max2.5A 5sec)
Vout: 5V or 12V (default 5V)
Vout Load Regulation: 2%
Max Duty Cycle: 95%
Output Ripple: 20mV (Vin=16V, Vout=12V@1.5A)
40mV (Vin=16V, Vout=5V@1.5A)
Pins distance: 2.54mm
Size: 17x11x3mm
Weight: 1g

Mini PDB & Linear Regulator 12V

This PDB is special used on the FPV Quad copter with 3~4S LiPo. Generally the input voltage of FPV camera is 7~13V, When 4S LiPo is mounted, the linear regulator can power the 12V camera & 12V LED without ripple & noise.

40*22mm PDB, 3g, Small & Light.
2oz copper board
Inbuilt 12V Linear regulator, Cont.500mA
Mounting: 24mm / Φ3mm

Mini POWER HUB w/ BEC 5V & 12V

Mini POWER HUB has been designed to provide the best possible performance and reliability in a small 36*36mm PCB. The HUB distributes power from a battery pack to 4 ESCs, as well as providing synchronised & regulated DC outputs for powering cameras, servos, video transmitters, LEDs, etc. Batteries may range from 3S to 6S LiPo. The HUB also features convenient solder bridge of various voltage for camera & video TX.

Specifications

General:

Input voltage range (3S-6S operation): 9 - 26VDC
Regulated 5V and 12V outputs
LED power indicators ( 5V & 12V outputs )
4 ESC outputs

ESC outputs:

Continuous current: 20A per output
Peak current (10 seconds/minute): 25A per output

BEC 5V output:

Designed for RC Receivers, Flight controllers, OSD, and Servos.
DC/DC synchronous buck regulator, Efficiency is up to 95%.
Voltage: 5.0 +/- 0.1VDC
Continuous current: 3 Amps
Short-circuit tolerant (10 seconds/minute)
LED (indicates voltage is in regulation)

BEC 12V output:

The battery should be 4S~6S LiPo
Standard output designed to power cameras and video transmitters,etc.
Voltage: 12.0 +/- 0.2VDC
Continuous current: 2 Amps (Max.3A 10s/minute)
Short-circuit tolerant (10 seconds/minute)
LED (indicates voltage is in regulation)

CAM & VTX voltage bridge

3S operation. choose “VCC” for 12V camera & 12V VTX, VCC=Battery Voltage.
4~6S operation, choose “12” for 12V camera & 12V VTX
3~6S operation, choose “5” for 5V camera
Video pass through from the “CAM” pad to the “VTX” pad

Physical:

Dimensions: 36 x 36mm
Weight: 6g
Mounting holes 30.5mm square spacing

PDB-XT60 w/ BEC 5V & 12V

MATEKSYS PDB-XT60 Power Distribution Board w/ BEC 5V & 12V
Input voltage range (3S-4S LiPo operation): 9 18V DC
Regulated 5V and 12V outputs
Can distribute power from a LiPo pack to 6 ESCs
For H or X type frame

UBEC DUO, 4A/5~12V & 4A/5V

This is a switch mode UBEC with duo output, takes 7~26V DC and convert into two output, one with adjustable 5V~12V 4A DC (remote controlled ON/OFF thru RC Aux channel) and one with fixed 5V 4A DC output. Because of that remote controlled ON/OFF switch, people like to use it on multi-rotors, camera gimbal, landing lights or bomb drop.

Features

Switch mode buck regulator
Two outputs
Built-in Aux control (On/Off) function
Low input voltage alarm and threshold setting
Output short-circuit protection

Specifications

Input voltage range : 7~26V DC (2~6S LiPo)
Out-1 : 5V, 6V, 7.2V, 12V adjustable, 0~4A, Max. 6A, built-in ON/OFF switch for RC Aux channel
Out-2 : 5V, 0~4A, Max. 6A
Efficiency : up to 95%
Standby current : 10mA
LiPo voltage alarm settings : 3.4V, 3.5V, 3.6V, 3.7V / Cell or OFF
Dimension : 58 x 36 x 8mm
Weight : 32g

Voltage Booster, 1S Li to 5V

Deskripsi Produk

Original Matek. Bukan clone/copy. Description: Input voltage range: 3~4.2V DC Output: 5V 2A Standby current: 5mA Pins distance: 2.54mm Size & Weight: 27x15x3mm, 2g Features: -VB2A5 is a compact, high-efficiency, synchronous step-up converter for a single-cell Li-ion/polymer battery. It can boost the voltage to 5V, allowing you to run a receiver on a single cell lipo. -Use for 1cell Li-ion or LiPo. -Synchronous step-up converter. -Guaranteed 2A Output Current at VOUT = 5V from 3.3V Input -Reverse input polarity protection. -Over-temperature protection. Package Include: 1x Voltage Booster

XCLASS PDB FCHUB-12S

PDB

Input voltage range: 8~60V (3~12S LiPo)
4x70A cont, 4x110A burst
4x ESC power /signal/ telemetry pads
Current Senor: 440A, 3.3V ADC, Scale 75
2x LED indicators for 5V, 12V

FFC connection

Compatible with MATEKSYS FC F405-STD, F722-STD
VTX: Video Transmitter signal
T5 & R5: TX5 and RX5 of F405-STD/F722-STD

BEC 5V output (5V pad)

Voltage: 5.0 +/- 0.1VDC
Continuous current 5 Amps, Max.6A
Short-circuit tolerant (2 seconds)
Overcurrent protection & self-recovery

BEC 12V output (12V pad)

Voltage: 12.0 +/- 0.2VDC (Input voltage >=12V)
Continuous current 4 Amps, Max.5A
Input voltage<12V, Output voltage = Input voltage
Probably there is audible sound in the BEC12V inductor when Input voltage<12V
Short-circuit tolerant (2 seconds)
Overcurrent protection & self-recovery

Switchable 12V output (SW12V pad)

12V ON/OFF can be switched via PINIO
can be use for powering VTX,LED etc.

BEC 3.3V output

Linear Regulator
Continuous current: 500mA

Physical

Mounting: 30.5 x 30.5mm, Φ3mm
Dimensions: 55 x 50 x 6 mm
Weight: 21g
1. 350~400°C, Sn63Pb
2. Enhance the pads nearby current-sense resistor with soldering

Lihat Juga