Hobbyking

10mm Shaft Universal Tri Motor Mount

Spec:
Shaft Size: 10mm
Inner Corner to Corner: 23mm
Outer Corner to Corner: 46mm
Weight: 7grams

6mm Shaft Universal Motor Mount

Spec:
Shaft Size: 6mm
Dimension: 64x45mm
Weight: 22grams

This multi function FPV Drone PDB For your Naze32/F3 flight controller has been engineered to provide racing performance and reliability. Enabling a crisp, solid power supply to your choice of ESC's and also supplying power in and out for cameras, transmitter LED's etc.

Power from can be supplied from a 2S to 6S LiPoly battery and supports On Screen Display (OSD) to show Volts, Amps, Timer & RSSI.
OSD supports MWODS firmware like Cleanflight, Betaflight & Baseflight.

This is a bulletproof PDB with OSD for your FPV Racing drones.

Features:
• Power distribution board+ 5V/12V BEC+OSD
• Support 2-6S input voltage
• 2oz copper foil, 4 layer boards to secure the base of large current
• Dual BEC, 5V/12V
• OSD function, support KVteam MWOSD firmware, comes with FTDI
• Supports OSD features such Basic Volts, Amps, timer & RSSI.
• 36 x 36mm size, same installation hole as Naze32, CC3D, SP3

Specs:
Input voltage: 5-24V DC (2-6S LiPoly)
BEC: 5V/2A & 12V/2A switchable
Maximum distribution current: 70A Constant, 100A Burst
Dimensions: 36 x 36 x 4mm
Mounting holes: 30.5 x 30.5mm M3 (Standard)
Weight: 7.3g

The HobbyKing Regulator switch is an easy and convenient way to add dual power redundancy to your electronics system. Simply use a pair of 7.4v Lipoly batteries and the system will provide dual 5.9v power outputs. The dual outputs can be used for 2 receivers or with a single receiver by using only one power output. In the case of a single output/single receiver configuration the output being used is supplied power by both batteries or a single battery in the case of a battery failure.

This system provides a stabilized voltage of 5.9v. Perfect for 6v Rx systems. This design enables you to use the latest lightweight Lithium-Polymer cells without exceeding the maximum voltage of 6.0 Volts.

The Hobbyking Sensor is equipped with LED power-on indicators for both power circuits. If you switch one battery on, the associated green LED glows. When both batteries are active, both LEDs light up.

The total voltage loss in the HobbyKing Sensor is about .35v which is so low that the volume of waste heat is almost negligible. The maximum continuous current is 5A which means it can easily handle up to 8 servos. However the rated continuous current of 5A does not reflect the capacity of the electronics which can handle much more for short periods, depending on ambient air temperature.

Do not allow the heat sink to exceed 60 Celsius


Specs:
Operating Voltage: 4~9v
Power Supply: One or Two 2S 7.4v Lipoly
Max Load: 5A cont.
Voltage Loss: 0.35v
Voltage stabilization: +/- .1v
Weight: 35g

Directions.
You cannot manually switch the current from one battery to the other, this is done automatically within the system.
The control functions consist of three push-buttons, two green LED’s and one red LED.
The buttons are marked SET, I and II.
The ‘SET’ button is to prepare the system. Holding the SET button in for 2 seconds ‘arms’ both internal switches, this will be shown by the red LED. After you have armed the system, press either or both I, II buttons to activate each battery.
Press and hold ‘SET’ to switch the system off again.

The Boom Stopper will help stop short circuits blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your batttery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating their is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

A great way to prevent issues with ESC reverse polarity problems and a must have tool for new build drones, with their multitude of wires, complex power distribution boards and numerous ESCs, it's easy to get a component reversed. You can avoid the chance of a costly mistake simply by using the Boom Stopper the first time you power up your project.

Oh and just in case you weren't sure DO NOT ATTEMPT TO FLY WITH THE BOOM STOPPER ATTACHED OR START YOUR MOTORS, it is purely to check that you don't have a fault in your wiring. With a 2A fuse you won't get very far if you do try.

Features:
• Includes LED fuse indicator
• Current limited to 2A

Specs:
Voltage: Up to 32VDC (2 to 8S LiPoly)
Current limitation: 2A
Cable Length: 160mm
Weight: Approx 24g

Includes:
1 x Cable with XT60 male and female connectors with inbuilt fuse
10 x 2A cartridge fuses

This small and lightweight Battery Eliminator Circuit (BEC) can be used in place of a dedicated battery to power your receiver and servos.

At a pre-determined voltage, the BEC will shut down power to the motor while continuing to power your receiver and servos. 

The HobbyKing™ Micro BEC 3A/5v features highly efficient switch mode circuitry that provides better heat dissipation compared to linear voltage regulation. The shielded PCB design and output EMF coil provide a stable, low noise voltage output.

This BEC also features built-in reverse polarity protection.

Specs:
Type: Switch mode BEC
Input: 6V~26V (2~6S LiPoly)
Output: 5V/3A Constant
Dimension: 16.5 x 16.5 x 8mm

Always double-check the polarity before connecting battery.

HobbyKing™ Micro BEC 5V/1A

This great new switching mode BEC is the smallest yet made by HobbyKing. Our engineers developed this with micro and race quads in mind. It is extremely small and light weight but gives you excellent power for the Fight Controller, RX, etc.

Specs:
Input: 2-4cells Lipoly
Connector: JST/Futaba
Output (Constant): 5v/1A
Type: Switching
Input protection: Reverse polarity protection
Size: 10x9x7mm
Weight: 1.4g (wires included)

The HexTronik UBEC Will supply a solid 5v or 6v to your reciever with a 2 to 5S Lipoly pack. UBECs are used by connecting the input wires to the battery and the output to the receiver. This allows your Speed Controller to run cooler, and safer as you now have an external circuit to power your receiver. Should the Speed Controller be overloaded and fail, you still have control of your plane.

Specs:
Output: 5v/3a & 6v/3a (Selectable)
Input: 5.5v~23v (2 to 5s)
Size: 41.6mm*16.6mm*7.0mm
Weight: 12.5g

Replacement "In-Line" UBEC for OPTO type ESC's

Specs:
Output: 3A Constant, 4A Max
Output Voltage: 5v
Input Voltage: 9v ~ 25v
Dimensions: 35mm x 13mm x 18mm
Weight: 15g

KINGKONG 5V 3A Switching Power UBEC

This UBEC has been designed for the KINGONG range of Multi-rotors but can be used in any multi-rotor. They can be used with 2-6S (7.4-22.2V) LiPoly batteries.

Specs:
Input Voltage: 6V~28V/DC (2-6S LiPoly)
Output Voltage: 5V
Ripple: Constant: 3 Amps
Dimensions: 53x17x7mm
Weight: 12g

Includes:
1 x UBEC

Simplify your next nitro powered model setup with our Linear BEC and Glow Driver 2 in 1 unit. This handy unit combines an onboard glow plug driver with a linear BEC to run your servos. Just one battery to handle the entire model. A small LED indicator board gives a series of warnings or displays what settings have been chosen, as well as the button to manually activate the onboard glow driver and doubles as your on/off switch. The onboard glow driver can also be remotely activated through your transmitter. When using it on a 3 position switch, you can select off, full power for startup, or half power which is great to make sure the plug stays lit as you come in to land and the engine is at idle. Running at half power also conserves battery and prolongs the glow plug's life.

For the Linear BEC portion, you can select between 5.9V output or 7.2V regulated output to get the most out of your high voltage servos. This regulated BEC can handle a constant current up to 5 amps, with burst current going as high as 20 amps. A low voltage warning on the LED board will alert you if the input voltage starts to get too low.

If you like clean installations and simplicity, check out our Linear BEC and Glow Driver 2-in-1. Less wires, and less batteries to charge make your life, and airplane or heli much simpler.

Features:
• Linear BEC and glow driver in 1 convenient unit
• Programmable BEC output voltage 5.9 V or 7.2 V
• Regulated BEC handles 5 amps continuous, or up to 20amps burst current
• Control the glow driver manually or by remote
• Can detect if glow plug is not working correctly
• Time out, short circuit, low voltage and overheat protection
• Low voltage alarm

Specs:
Input Voltage: 7.4V (2S LiPoly)
Output Voltage: 5.9 or 7.2V
Constant Current: 5A
Burst Current: 20A (10 Sec)
Input Connector: JST

*Note: Instructions are located in the files tab below.

Matek Micro BEC 5V/12V-Adj

A Highly efficient synchronous rectified step-down switch mode converter. It offers a very compact solution to achieve 1.5A continuous output current over a wide input supply voltage (7 to 21V).

Features:
• High-Efficiency Synchronous Mode
• Wide 7V to 21V Input range
• Voltage output can be 5V or 12V adjustable. (default is 5V)
• OCP Protection and Hiccup
• Thermal Shutdown
• Output Short-circuit tolerant (5 sec/minute)

Specs:
Continuous load current: 1.5A (Max2.5A 5sec)
Vout: 5V or 12V (default 5V)
Vout Load Regulation: 2%
Max Duty Cycle: 95%
Output Ripple: 20mV (Vin=16V, Vout=12V@1.5A)
                          40mV (Vin=16V, Vout=5V@1.5A)
Pins distance: 2.54mm
Size: 17x11x3mm
Weight: 1g

Generally the input voltage of an FPV cameras is 7 ~ 13V with a 4S LiPoly input, the Matek systems linear regulator can convert 14 ~ 17V to 12V, and can power camera and/or 12V 1W LEDs without ripples or noise.

This simple step down regulator is ultra lightweight and comnpact and is suitable for even the smallest of builds.

Specs:
Dimensions: 25 x 10 x 3.5mm
Weight: 1g
Input: 4S LiPoly
Output: 12V continuous, 300mA

The 5 in 1 V3 system has been engineered to provide the highest possible performance and reliability in a 46 x 36mm sized PCB. The 5 in 1 system combines a printed distribution board (PDB) with 5v-3A / 12v-500mA BEC, LED light controller, lost model finder and low voltage alarm functions.

The 5 in 1 system has been specifically designed for use with 250 sized racers, though its is also suitable for larger multirotors. The built-in 5v BEC can be connected to receiver or flight controller with aux pins directly to simplify your set up. The 12v BEC can be used to power the camera and video transmitters.

The built-in 5v LED light controller has 3 light modes which can be set up to change with the toggle switch on your transmiter. The lost model buzzer can also be triggered with the toggle switch making it super easy to find your multirotor in the event of an incident. The 5 in 1 system also acts as a battery voltage monitor. Once voltage gets below the set threshold the audible buzzer & LED light will remind you.

Features:
• 5 in 1 function
• Compact & light weight
• 2oz copper & 4 layered PCB design
• Paired ESC & battery solder tabs
• BEC 5v & 12v output LED indicators
• TVS input protection

Specs:
Input Voltage Range: 7~26v DC, 2~6 Cell LiPoly
Dimensions: 36 x 36 x 6mm
Weight: 7g
Mounting: 30.5mm, F3mm

Package Includes:
1 x 5 in 1 power system
1 x Nylon fixing set
1 x Jumper cable

The Quanum QM12V5A-UBEC is an advanced switching regulator that will supply 5-8 amps of power for your servos and accessories. The UBEC has an input range of 7.2-25.2v (2-6 cell Lipo) and has a switchable voltage output (7.2V/12V). The UBEC also features an inline noise reduction filter and dual output connectivity, which allows you to power servos and additional accessories independently!

Features:
• 5A power output (8A Bursts)
• Switchable voltage output (7.2/12V)
• Dual output connectivity
• In-line noise reduction filter

Specs:
Output: 5A continuous, 8A burst rate
Input: 7.2v - 25.2v (2-6s Lipo)
Size: 55 x 28 x 10mm
Weight: 32.5g

* To enable 12V output, input voltage source need to be at least 12V.

Here's a tidy dual switch solution for your Nitro or Gas aircraft.

The unit features a black all alloy housing, a single RX switch, a charge/voltage check port and an integral fuel filler dot. A great looking single service point solution for your models!

Charge up, Fuel up - GO!

Spec:
Length: 62mm
Width: 23mm
Mounting depth: 33mm
Cable length: 200mm
Weight: 28.5g

The Spider Pro UBEC is the perfect partner to your Spider Pro and Spider Pro Premium Opto speed controller equipped multicopter. Provides a smooth 5V/2A power source to run all your onboard equipment and is super lightweight at only 1g.

Specs:
Continuous Current: 2A
Voltage Output: 5V
Input Voltage: 2~6S (7.4~22.2V)
Length: 12mm
Width: 10mm
Height: 4.5mm
Weight: 1g

See under "Files" tab for manual.

Push the style and add a finishing touch to your DIY projects. These 316 stainless steel illuminated LED push button on-off switches have a standard 169mm thread, stainless shell and button. Built tough and able to handle 50,000 cycles.

What are you waiting for... Push the button !

Features:
• LED illuminated button
• 316 stainless steel
• Copper plated terminals
• Silver tin oxide contacts
• 50,000 cycles

Specs:
Length: 35.8mm
Diameter: 17.8mm
Thread: 16mm
Function: Off/On
Operating stroke: 1.5~2.5mm
Operating Temp: -30~85 centigrade (ISA)

This receiver switch features an in built ultra high brightness LED receiver battery voltage display which is clearly visible in direct sunshine.

Additionally this switch incorporates a remote control CDI ignition master switch as an added safety feature for Gas engine users.

Independent CDI power & receiver power supply sockets. The Receiver's power is completely isolated from the CDI power circuit, so there's no risk that the CDI high frequency signal will interfere the receiver.

The receiver switch itself is rated as 15amps continuous.

Note: No BEC - voltage input equals voltage output

Specs:
Channels: 1 (AUX) for CDI Ignition Switch
Input Voltage: 5-6v
Switch limitations: RX 15amps; CDI 5amps
Output voltage: Same as input
Weight: 32g
Volume: 40mm  x 27mm  x 35mm

The Turnigy 3 Function Switch features a built-in 5 Amp multi-voltage UBEC and an ultra high brightness LED voltage display which is clearly visible in direct sunshine. It displays in real time, both the UBEC input and output voltages.

Input voltage range is 6-13V, which can be directly supplied by Lithium, NiMh, or NiCd cells. Suggest battery with JST connector.

The UBEC output voltage is switchable between 5.2 or 6V. 

Features:
• Molded plastic case
• Heavy duty 22awg leads
• Easy mounting tabs
• Selectable output voltage
• Displays both input and output voltage

Specs:
Input voltage: 6—13V
Output voltage: 5.2/6V
Output current: 5 Amps (MAX: 8A)
Weight: 28g
Volume: 40mm  x 27mm  x 35mm

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Specs.
Turns: 22T
Voltage: 2~3S Lipoly
RPM/V: 1460kv
Internal resistance: 0.045 Ohm
Max Loading: 33A
Max Power: 430W
Shaft Dia: 4.0mm
Bolt holes: 25mm
Bolt thread: M3
Weight: 75g
Motor Plug: 3.5mm Bullet Connector

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival but surpasses the quality of many leading motor manufacturers on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Specs.
Turns: 18T
Voltage: 6~10S Lipoly
RPM/V: 280KV
Internal resistance: 0.031 Ohm
Max Loading: 60A
Max Power: 1510W
Shaft Dia: 6.0mm
Bolt holes: 25mm
Bolt thread: M4
Weight: 369g
Motor Plug: 4mm Bullet Connector

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival but surpasses the quality of many leading motor manufacturers on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Specs.
Turns: 10T
Voltage: 10S Lipoly
RPM/V: 236KV
Internal resistance: 0.019 Ohm
Max Loading: 60A
Max Power: 1850W
Shaft Dia: 6.0mm
Bolt holes: 25mm
Bolt thread: M4
Weight: 530g
Motor Plug: 4mm Bullet Connector

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufacturers on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Specs.
Turns: 6T
Voltage: 10S Lipoly
RPM/V: 320kv
Internal resistance: 0.014 Ohm
Max Loading: 70A
Max Power: 2220W
Shaft Dia: 6.0mm
Bolt holes: 25mm
Bolt thread: M4
Weight: 531g
Motor Plug: 4mm Bullet Connector

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival but surpasses the quality of many leading motor manufacturers on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Specs.
Turns: 18T
Voltage: 12S Lipoly
RPM/V: 149KV
Internal resistance: 0.021 Ohm
Max Loading: 70A
Max Power: 2250W
Shaft Dia: 8.0mm
Bolt holes: 32mm
Bolt thread: M4
Weight: 840g
Motor Plug: 4.0mm Bullet Connector

Get some BOOST out of your car!

Similar to the Kinetic Energy Recovery System (KERS) used in Formula One, the Turnigy ENOS Booster will pre-charge a small amount of power in the capacitors while the system is inactive. Once you activate the Booster (via spare radio channel), extra power will kick-in for a short period of time by increasing the voltage for the ESC.
You can control the Boost in real-time by using the 3Ch button on the radio.

Turnigy ENOS In-line Electronic Booster will give you a great advantage when you want to over-take your rival on the straight or have instant acceleration at the corner exit.

Let's Boost-Up!!

Specs:
Input Voltage: 6-14v (2-3s LiPoly)
Maximum Capacitor Charging Current: 3.5A
Maximum Capacity Voltage: 3.5A
Freezing Time (Vcap < 0.8V): 2 seconds
Farad Capacity: 30F
Charge Time: 20 Seconds
Signal Pulse: >1300ms On, >1300ms Off
Weight: 58g
Connector: XT60 (male / female)

The Turnigy Heavy Duty Receiver Switch features an in built ultra high brightness LED receiver battery voltage display which is clearly visible in direct sunshine. The molded plastic case has tabs for easy mounting to your airframe with the included screws.

The receiver switch is rated as 15amps continuous. This is a on/off switch only, there is no voltage regulation.

Features:
• Molded plastic case
• Heavy duty 22awg leads
• Easy mounting tabs

Specs:
Input Voltage: 4-13v
Limitations: RX 15amps (20amp peak); CDI 5amps
Output Voltage: Same as input
Weight: 27g
Volume: 40mm  x 27mm  x 35mm

The Turnigy HV SBEC 5A Switch Regulator is perfect for large electric models using high voltage power setups. With its high voltage (8-42V) input capability, you will have the option to run this unit off of your main battery or off a separate 2-10S lipo. This voltage regulator will provide a sustained 4A output at 5V or 6V, and has a max current capability of 5A.

Give your RX and servos the power they need with this high quality HV SBEC by Turnigy.

Specs:
Input Voltage: 8-42V (2-10S Lipo)
Output Voltage: 5V or 6V (user selectable)
Max Load: 4A continuous/5A max
Weight: 21g
Dimensions: 59x10x25mm

Turnigy introduce the Min Power Distributor (Green) suited to 20cc plus gas powered models.

This unit has great features, which include: Dual battery input to increase reliability, 8 channel RX input with dual outputs on each channel - simplifying dual servo control surfaces.

This is the first Power Distributor system to securely nest the receiver within the power distribution 'block' thereby shortening cable runs, adding protection to your all important receiver & speeding set up time.

Note: This Power Distributor passes battery input voltage to all connected devices

Features:
• 8 input channels
• 16 output channels
• 3 Status check LEDs
• Padded receiver tray & Secure mounting

 Specs:
Input channels: 8
Output channels: 16
Input voltage: 5-6V
Max output load: 30A
Output voltage: Input voltage pass through
RX power: Input voltage pass through
Working temperature: -20 to 85 degrees c
Weight: 84g
Dimensions: 116mm x 88mm x 13mm

Turnigy introduce the Min Power Distributor UBEC (Red) suited to 30cc plus gas powered models.

This unit has great features, which include: Dual battery input, 5v isolated linear RX BEC, 8 channel RX input with dual outputs on each channel - simplifying dual servo control surfaces.

Great inclusions are the independent 5V linear regulator providing a separate power source for the receiver, optically isolated CDI power & in built remote ignition kill. Receiver, Servo & CDI power sources are completely isolated from each other.

Three selectable UBEC operating voltage options (via Jumper):

Direct connection: uses 5V- 6V input to supply power - voltage pass through from battery input to Receiver
Voltage drop 0.5V: Reduces a 6v input to 5.5v
Voltage drop 7805: use 7.2V- 8.4V input to supply 6v regulated power

This is the first Power Distributor system to securely nest the receiver within the power distribution 'block' thereby shortening cable runs, adding protection to your all important receiver & speeding set up time.

Features:
• 5v adjustable RX BEC
• 30 Amp Servo
• 8 (+1 CDI cut) input channels
• 16 output channels
• 5 Status check LEDs
• Padded receiver tray & Secure mounting
• CDI isolated power
• CDI remote ignition control (remote cut)
• CDI power status indicator light
• CDI power output terminal
• CDI voltage monitor LED

Optional: Input/output voltage display with external power switch

Specs:
Input channels: 8
Output channels: 16
Input voltage: 5-8.4V
Servo Current: 30A (40Amp Burst)
Rx voltage: 5-8.4V (user adjustable; Default is voltage pass through)
Working temperature: -20 to 85 degrees c
Weight: 80g
Dimensions: 116mm x 88mm x 13mm

If you have ever had an ESC burn or battery suddenly drop voltage mid-flight then you will understand the importance of having a rock solid system powering your receiver and servos.
With instant failover protection the TURNIGY Redundant DUAL 8A UBEC system is an easy choice for anyone flying large scale aircraft.
The Dual 8A UBEC controller instantly switches to the second UBEC in case of a short, burnout, or power loss (faulty battery). The LED indicates #1 or #2 UBEC live status, over voltage (short) or low battery voltage.
The TURNIGY Redundant Dual 8A UBEC can be connected to one or two battery packs and provides redundancy in the case of an electronic, connection or battery failure. In most cases UBEC''s fail when an FET burns, shorting the circuit, frying your battery and cutting power to your receiver. This system prevents that by keeping the circuit open and switching source to the second UBEC and battery.

A must have for larger size aircraft!

Spec.
Input: 6.6~8.4V (2 cell Lipoly) [Two battery or two conn. to the same battery]
Output:  5.9V(+/-0.5V)
Max Load: 8A
Weight: 49g
VR Mode: Linear

Included.
Dual Redundant 8A UBEC x 2
Dual Redundant Controller x 1

This product is designed and manufacturered in house. Stock arrives frequently (every few days).

The Turnigy TrackStar Sensored Brushless Motors offer outstanding performance at an incredible price!

Featuring a quality CNC motor can, hand-wound high purity copper windings and powerful sintered neodymium magnets, you wont find a better priced motor of this caliber anywhere else! The integrated sensor ensures smooth startups and acceleration.

The TrackStar brushless motors make a great upgrade for 1/8th short course trucks, monster trucks, buggies or anything else that uses 42 size motors.

Features:               
• Sensor-Based for Excellent Torque and Low-Speed Driveability
• Compatible with any Sensored/Sensorless ESC
• CNC Aluminum Motor Can  
• High Purity Copper Windings
• Removable/Replaceable Rotor       
• Powerful Sintered Neodymium Magnet    
• Precision Engineered for Maximum Energy Conversion

*Note: Sensor cable included

Specs:
Size: 4270
RPM/v: 1900kv 
Poles: 4
Sensored: Yes (Standard 6 pin harness)
Max voltage: 15V (4S)
Max Current: 120A
Max Watts: 1800W
Resistance: 0.012ohm
Shaft Size: 5mm
Can Diameter: 42mm
Can Length: 70mm
Weight: 329g

Dr. Mad Thrust series 3A BEC with Inbuilt Aux Controlled On/Off Switch for Accessories - An efficient switching regulator providing a reliable and efficient 3A (5A burst) power supply for your RX, which is 5v or 6v selectable via a jumper plug. Input voltage ranges from 7.4v (2s) to 30v (8s) and the unit has been designed to offer minimal output noise.

Uniquely, this BEC also features an inbuilt power switch that is operated by a spare Aux Channel, this feature can be used to power and switch on/off a wide variety of features such as navigation/landing lights, bomb drop, canopy operation and of course our Dr Mad Thrust machine gun sound module and machine gun LED system (see related items below) via an AUX channel on your RX....in fact at 2A output, the inbuilt power switch can handle a huge variety of features you may want to fit to your model!

Specs:
Input Voltage: 7.4v~30v (2s~8s Lipo)
Output Voltage: 5v/3A or 6v/3A
Output Current: 3A Continuous or 5A burst
Quiescent Current: 20mAh
Electronic Switch Output: 2A, 5V or 6V
Dimensions: 40mm x 11mm 23mm
Weight: 26g

Dr. Mad Thrust series 5A HV BEC with Inbuilt Aux Controlled On/Off Switch for Accessories - An efficient switching regulator providing a reliable and efficient 5A (7.5A burst) power supply for your RX, which is 5v or 6v selectable via a jumper plug. Input voltage ranges from 7.4v (2s) to 42v (11s) and the unit has been designed to offer minimal output noise.

Uniquely, this BEC also features an inbuilt DC switch that is operated by a spare Aux Channel, this feature can be used to power and switch on/off a wide variety features such as navigation/landing lights, bomb drop, canopy operation and of course our Dr Mad Thrust machine gun sound module and machine gun LED system (see related items)....in fact at 2A output, the inbuilt switch can handle a huge variety of features you may want to fit to your model!

Specs:
Input Voltage: 7.4v~42v (2s~11s Lipo)
Output Voltage: 5v/3A or 6v/3A
Output Current: 5A Continuous or 7.5A burst
Quiescent Current: 20mAh
Electronic Switch Output: 2A, 5V or 6V
Dimensions: 50mm x 12mm 28mm
Weight: 30g

UBEC DUO 4A/5~12V & 4A/5V

This device is a high-efficiency, switch-mode buck regulator with two output channels, works with 7~26Vdc input. One output channel is capable of supplying 0~4A/5V for your RX or Flight Controller. This device also features another output channel with 4A & 5~12V (adjustable), inbuilt power switch that is operated by a spare Aux Channel, this feature can also be used to power and switch on/off a wide variety of electric equipment, such as Multi-rotor Gimbals, Video Transmitters, FPV camera systems, HV Servos, navigation/landing lights, bomb drops, etc.

Features:
• Switch-mode buck regulator
• Two output channels
• Built-in Aux control (On/Off) function
• Low input voltage alarm & threshold setting
• Output Short-circuit protection

Specs:
Input voltage range: 7~26V (2~6S LiPoly battery)
Out-1: 5V, 6V, 7.2V, 12V (adjustable), 0~4A, Max 6A, inbuilt Aux control switch
Out-2: 5V, 0~4A, Max 6A
Efficiency: up to 95%
Standby current: 10mA
LiPoly voltage alarm setting: 3.4V, 3.5V, 3.6V. 3.7V/Cell & OFF
Input cable: 20cm (Silicone 20 AWG)
Output cable: 30cm (2pairs, Silicone, 22AWG)
Size: 58x36x8mm
Weight: 32g

Universal Mount - M3.5 Fastener kit

Included:
M3.5x17mm Screw * 4
M3.5x12mm Screw * 4
10x4x2mm Washer * 4
10x4x1mm Washer * 4

Voltage Booster 3-13V to 5-15V

This is a high-efficiency, adjustable boost (step-up) voltage regulator generating high output voltages from input voltages as low as 3V. The available output current is a function of the input voltage, output voltage and efficiency but the input current can typically be as high as 5A. There is Integrated reverse-voltage protection, over-current protection, over temperature shut-off and under-voltage lockout.

Features:
• Efficient voltage step-up
• Reverse-voltage protection
• Over-current protection
• Over temperature shut-off
• Under-voltage lockout
• Mounting holes for two M2 screws

Specs:
Input voltage: 3V-13V
Output voltage: 5V-15V (adjustable)
Maximum output current: 3A
Standby current: <10mA
Typical efficiency: 80%~95%
Size: 37x19x4mm
Weight: 3.5g

Included:
1x Module

Voltage Booster 5V/2A

This is a compact, high-efficiency, synchronous step up converter for a single-cell Li-ion/LiPoly battery. It can boost the voltage to 5V, allowing you to run a receiver on a single cell LiPoly.

Features:
• Use for boosting the 1S Li-ion or LiPoly to 5V
• Synchronous step-up converter
• Guaranteed 2A Output Current at VOUT = 5V from 3.3V Input
• Reverse input polarity protection
• Over-temperature protection
• Power supply for receiver

Specs: 
Input Voltage: 3V - 4.2V DC
Output Voltage: 5V 2A
Pins Distance: 2.54mm
Standby Current: <5mA
Size:  27x15x3mm
Weight: 2g

Included:
1 x Module

This small and lightweight UBEC features a high efficiency switch mode design providing better heat dissipation when compared to the linear voltage regulators. The 3.3V output is ideal for use with robotics, LED and DIY projects. The shielded PCB design and output EMF coil makes helps provide a stable and low noise voltage output. This UBEC also features built-in reverse polarity protection.

Specs:
Input: 7V-23V (2-5S Lipoly, 3-6S Li-Fe or 5-15S NiXX Battery Pack)
Output: 3.3V/3.5A (Less than 50mV peak to peak voltage @ 2A)
Dimension: 47mm x 25.2mm x 10.8mm (LxWxH)
Weight: 11.7g (wires included)

*Note: An instruction manual for this item is available from the files tab below.

This small and lightweight UBEC features a high efficiency switch mode design providing better heat dissipation when compared to the linear voltage regulators. The shielded PCB design and output EMF coil makes helps provide a stable and low noise voltage output. This UBEC also features built-in reverse polarity protection.

Specs:
Input: 7.2V-21V (2-5S Lipoly, 2-6S Li-Fe or 5-15S NiXX Battery Pack)
Output: 9V/3A (Less than 50mV peak to peak voltage @ 2A)
Dimension: 47mm x 25.2mm x 10.8mm (LxWxH)
Weight: 11.7g (wires included)